Here’s how to use quick splice connectors to add a wire connection quickly and easily! Also, they may not always be the best option for joining wires together! This connector is sometimes called a vampire connector since they “bite” into the wire and draw power from a power source. These solderless wire connectors may provide a quick connection, but are sometimes more trouble than they are worth. A soldered connection typically provides a better connection and longer service life than a wire tap, splicer, or runtap.
Here’s where to get some if you aren’t convinced not to get them:
Red (18-22 AWG) Scotchlok connectors: *
Blue (14-16 AWG) Scotchlock connectors: *
Yellow (10-12 AWG) Scotchlok connectors: *
(With all of these, read the description for more details. There are a ton of options out there for different features, sizes, etc.)
Some pliers: *
•
Check us out on Twitter, Instagram, Facebook, and more:
(Sometimes previews and exclusive content are shared on these platforms!)
Cars Simplified is a show dedicated to automotive education, including DIY repair, automotive news, auto industry changes, automotive technology, performance modifications, and more, all presented in a friendly and easy to digest manner!
#CarsSimplified #CarsSimplifiedS7 #CSQuickTips #CarsSimplifiedQT #AutomotiveElectrical #Wiring #Electrical #Automotive #Cars #HowTo
Disclaimer:
Due to factors beyond the control of Cars Simplified, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. Cars Simplified assumes no liability for any property or personal damage that may arise from doing a repair on your vehicle after watching any video. Due to factors beyond the control of Cars Simplified, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Again any injury, damage or loss that may result from improper use of tools, equipment, or the information contained in this video is the sole responsibility of the user and not Cars Simplified.
* Cars Simplified earns from qualifying purchases via the Amazon Associate program.
Visit Sources Channel
Just an opinion but you should mention what you would recommend doing for automotive applications instead of just saying don't do it multiple times.
Solder shouldn’t be used for automotive wiring. The absolute worst for that environment
Good video, thanks.
But super shitty connectors, avoid.
would these work for say automotive audio wiring ?
After connecting, why not just use some electrical tape to secure them?!
They are PERFECT for automotive wiring. I dont know what went wrong with this guys build but my LED bumper lights are spliced to my tail lights when in reverse and Ive had ZERO issues. If you use the correct size, I dont see the issue. Also, use SOLID core wiring with these. Not braided or twisted core.
Sorry, Im a Flux, Tin and solder and adhesive lined shrink wrap man. especially when the connection can get wet.
This may sound stupid but is there any way to remove it ?
What if you wanna take these off? Does anything happen to the main wire?
Would you recommend using these for installing a line output converter onto a factory radio?
Finally, a video demonstration that was actually helpful! Ive watched several videos where the person demonstrating just explains in words how he did it, and not actually showing the process visually Lol
So what type quick connector SHOULD I use??
Those connectors are garbage use solder or loop and heat shrink those connectors corrode fall off and are horrible You're asking for trouble. Learn how to solder it's the best connection you can make when it's done right
HHFIUF
How do i remove them
If you need high beam signal for your LED bar you just put on your winter car that goes to the last highway in spring anyways? Yes.
In every other case? Hell no.
Hi am not sure what size to buy if it's 18/14, 11/18 am going to splice my rear brake lights? Thanks
Thank you for this video!
Is that type of quick splice connectors limited to 12 v ? I am not sure if it is safe for 120 v household current , am I correct? If so, is there similar quick splice for 120 V?
Problem with these is mostly user error, not crimping down hard enough, using wrong size wire, and not water/weather proofing with tape for outside applications. When done right they work great and last a long time.
they work fine in auto wiring lol!
Just wrap it in tesla tape when done, you'll be perfectly fine.
I'm planning to use this on my motorcycle and I've been thinking to apply a dielectric grease for protection from moist or water, will this be a good idea?
how do I wire a 24 gauge to a 22 gauge it's been year since I've installed my stereos
I use em in my pick up for headlight and aux lighting… 2 years of off-roading and daily driving? Still running like a champ.
Are these connectors only to run a single wire to connect to another single wire? Or would I be able to run an LED light to my headlights with this? So they could turn on and off with my headlights
I've never understood why people use resistors to fix fast flash. Doesn't this increase current draw, which is one of the reasons to use LED lights, to reduce power requirements? The proper flasher relay is the method I use. I am wondering if what I think I know is wrong.
i use them in my vehicle, interior only, haven’t had a problem
How these be Good if i use them for the Head light Led i bought for my truck ?
Isn’t working for me, its the correct guage, but when it cuts down on one of the wires, it doesnt go all the way through the insulation, only a small piece shows and my backup camera isn’t powered. Should I use a smaller one?
thanks just installed a rear camera and it wasnt working, i didnt push down on the metal all the way
So you’re saying not to use them, but you didn’t tell us what to use instead.
Thanks.
Well 💩 or as spalding would say “double 💩s”….
Yeah I’m planning on using this to wire together upfitter switches and box lights in my raptor, hopefully it’ll work well
Thanks You made my decision for me I was going to use these in a kayak but the wires will move around and will be exposed to moisture so its off the table back to solder and shrink tubing.